A monopole antenna with cotton fabric material for wearable applications

Scientific Reports volume 13, Article number: 7315 (2023) Cite this article

1134 Accesses

2 Altmetric

Metrics details

A monopole antenna operated at 2.45 GHz and embedded with artificial magnetic conductor (AMC) for wearable communication systems is investigated in this article. The proposed antenna is composed of a metalized loop radiator with a coplanar waveguide microstrip feedline which is affixed on a cotton fabric material substrate. As well, a cotton-based AMC surface is utilized to eliminate the body’s absorbed radiation and enhance the gain of the antenna. It is composed of 5 × 5 array unit cells etched with I-shaped slots. Using this configuration, simulations show that the specific absorption rate (SAR) level was significantly reduced. Considering flat and rounded body parts, it was found that the SAR values averaged over 10 g at a distance of 1 mm away from the tissues model were only 0.18 W/kg and 0.371 W/kg, respectively. Additionally, the antenna gain was improved up to 7.2 dBi with an average radiation efficiency of 72%. Detailed analysis with experimental measurements of the cotton-based antenna for different operation scenarios is introduced. The measured data show a good correlation with the electromagnetic simulation results.

Nowadays, WBANs are applied in healthcare and medical applications1,2,3. In WBANs systems, wearable antennas are vital components used for communication near the human body4,5,6. This challenging role is reflected in the considerations that take when designing such types of antennas. One of these considerations is the influence on the antenna resonance behavior due to the loading effect of the high permittivity body tissue7,8. On the other hand, in antenna design choosing flexible materials have to be considered to be utilized close to the rounded parts of the human body. Several kinds of wearable antennas based on flexible materials are studied and investigated by researchers such as textile9, flexible substrate10, dielectric resonators11, polyimide12, polydimethylsiloxane13, paper14, and Kapton15. Among these materials, textiles are preferred due to their lightweight and high flexibility in integration with clothing16. However, the implementation process of wearable antennas using textile fabrics as substrates is more difficult compared to the use of conventional substrates17.

As wearable antennas operate near the human body, their radiation can cause damage to body tissues. This effect is examined by evaluating the SAR level by considering a specific part of the human body. To reduce the health risks introduced by the wearable antennas, the SAR values should be below the regulated level18,19. In the literature, several techniques have been reported to reduce the body's absorbed radiation and, consequently, minimize the SAR level20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36. One of the common techniques is using a reflector below the antenna. Different structures have been utilized as reflectors such as high impedance surfaces (HISs)20, electromagnetic bandgap (EBG) structures21,22,23,24,25,26, and artificial magnetic conductor (AMC) surfaces27,28,29,30,31,32,33,34,35,36. These structures can increase the antenna gain and help significantly reduce its overall profile compared to the use of a traditional perfect electric conductor (PEC) structure.

Among the reported reflector structures, AMC surfaces have been widely used for backing wearable antennas27,28,29,30,31,32,33,34,35,36. In27, a flexible reconfigurable antenna backed with an AMC surface that worked at 2.4/3.3 GHz was introduced. Considering a human leg model, the evaluated SAR values do not exceed 0.29 W/kg for both operating bands with increasing in the antenna gain by 3.6 and 2.4 dB, respectively. In28, a Yagi–Uda antenna built on a latex substrate and combined with an AMC surface was presented to operate at 2.4 GHz. Single- and double-layered AMC surfaces were used to minimize the peak SAR level to 0.714 W/kg and increase the peak gain up to 1.8 dBi. In30, the performance of a wearable antenna over an AMC surface based on using a stretch conductive fabric was investigated. The design enabled the antenna to cover both WiFi and the 4G long-term evolution (LTE) frequency bands.

A textile antenna with AMC surface for WLAN/WBAN applications was reported in32. The integrated geometrical configuration reduced the SAR value and improved the gain to 0.0721 W/kg and 2.42 dBi, respectively. In33, a flexible AMC surface was used as a reflector. It provides stable performance and reduction in SAR level. In the reported study, the effect of crumpling of the integrated antenna was analyzed. In34, a flexible antenna backed with an AMC ground plan and operates at 2.4 for telemedicine applications is reported. Utilizing the AMC plane provides a 3.7 dB increase in gain, in addition to a 64% reduction in SAR value. A design of compact wearable antennas resonated around 2.65 GHz is reported in35. The backward radiation was reduced using a metasurface recognized as an AMC plane and modeled with a CRLH transmission line operated at negative modes. The peak SAR value of the proposed antenna is 1.25 W/kg for a 5 mm gap from the human body with a real gain of 0.82 dBi. A dual-band 1.57/2.45 GHz wearable antenna with AMC structures is discussed in36. The antenna has a SAR level lower than 0.12 W/kg and a gain value of about 1.9 dBi at the two bands.

In this work, a design of a cotton-based wearable antenna over an AMC surface is proposed for 2.45 GHz applications. The integrated antenna adopts cotton fabric as a substrate to ease integration into clothes. In the CST Microwave Studio, the performance and radiation results demonstrated that the antenna provides excellent on-body performance and achieved SAR values below the regulated limit. Detailed discussions on antenna designs with comparative analysis with recent relevant work were presented. Based on the numerical model, the proposed antenna and the AMC surface were fabricated, integrated, and tested. Good agreements between simulated results and measured data were observed. In the end, we can conclude the contributions of the work as,

The proposed antenna is fabricated on textile material to achieve lightweight and high flexibility when integrated with clothing.

The deformation of the integrated antenna was analyzed in free space as well as when it was placed in the vicinity of the human body, indicating its good suitability for operation when bent at both the x-axis and the y-axis.

The integrated antenna has a realized gain of 7.2 dBi with average radiation and total efficiency of 72% and 60%, respectively.

The integrated antenna has a low SAR level averaged over 10 g at a distance of 1 mm away from the tissues model where only 0.18 W/kg and 0.371 W/kg, respectively.

The design steps of the proposed wearable monopole antenna are depicted in Fig. 1a. The antenna is built on a 0.9 mm single-layer cotton fabric with a relative permittivity of εr = 1.7. A metallic layer is manually attached to the fabric-base substrate to form the antenna radiator and ground plane. As illustrated in the figure, Antenna 1 consists of an L-shaped radiator fed by a 50Ω co-planar waveguide (CPW) line as the first step of the design. With this configuration, a weak resonance around 3.1 GHz is achieved, as shown in Fig. 1b. To enhance the antenna performance, Antenna 2 is designed, where the radiator is extended to a C-shaped. Figure 1b shows that Antenna 2 can operate around 3.3 GHz with good matching performance. Finally, to tune the antenna resonance to the desired frequency band around 2.45 GHz, an antenna with a loop radiator is designed. The optimized design parameters are listed in the caption of Fig. 1, which shows that the proposed antenna can resonate around 2.45 GHz with a bandwidth (BW) extended from 2.29 to 2.69 GHz (10 dB return loss).

(a) The design steps of the proposed wearable antenna (L = 36 mm, W = 30 mm, L1 = 10 mm, L2 = 16 mm, W1 = 23 mm, W2 = 16 mm, Lr = 2 mm, Lf = 15 mm, Wf = 3.5 mm, Lg = 7 mm). (b) Simulated |S11| responses versus frequency.

To eliminate the body's absorbed radiation and enhance the antenna gain, the proposed antenna is placed on an AMC surface to reduce the overall profile of the entire structure compared to the use of the PEC surface. Such surfaces operate as inductor–capacitor (L–C) tank circuit at the resonance frequency and achieve HIS. The proposed AMC surface is designed to achieve in-phase reflection at the antenna’s resonance frequency of 2.45 GHz. It was built on a double-compacted layer of cotton fabric with a thickness of 1.8 mm. It consists of 25 square patch unit cells (5 × 5 array) with I-shaped slots, which occupy a whole area of 122.5 × 122.5 mm2. The geometrical configuration of the proposed unit cell and its equivalent circuit are depicted in Fig. 2a,b, respectively. The ADS software is used to model the equivalent circuit, where the ground plane, the substrate, the I-shaped slot, the rectangular patch, and the gap, g is modeled as Lground, Cd, Cslot, LP, and Cg, respectively37,38. The optimized lumped element values are displayed in the caption of Fig. 2. The outcome of the circuit simulation is compared with that of the EM simulation and shown in Fig. 2c. A good tendency between the two outcomes is observed. The in-phase (− 90° to + 90°) frequency range is 2.4–2.5 GHz with 0° phase at 2.45 GHz. The effect of the length, Ld and width, Wd of the I-shaped slot on the phase response is illustrated in Fig. 3a,b, respectively. It can see that, the 0° phase is shifted up with the increase of the Ld, while it shifted down with the increase of the Wd. The optimized values of the Ld and Wd are 13 and 22.3 mm, respectively. The surface current density distribution at 2.45 GHz is examined in Fig. 4. As can be seen, the currents are distributed around the edges of the slot.

(a) Proposed square patch unit cell of the AMC surface. (a) Geometrical configuration (Ls = Ws = 24.5 mm, Wd = 22.3 mm, Ld = 13 mm, d = 2 mm, g = 0.25 mm). (b) Unit cell equivalent circuit model (Cg = 2.942 pF, Cd = 2.452 pF, Cslot = 4.85 pF, Lp = 5.842 nH, Lground = 1.42 nH). (c) Simulated reflection phase responses versus frequency.

Effect of the length, Ld (a) and width, Wd (b) of the I-shaped slot on the phase response.

Illustration of surface current distribution on the proposed square patch unit cell of the AMC surface at 2.45 GHz.

In this section, the performance of the single-band wearable antenna over the designed AMC surface is investigated. Two significant parameters that affect the antenna’s performance were subjected to study, the spacing of the AMC surface below the antenna and its array size. Parametric studies were carried out to adopt these parameters. Figure 5a,b show the influence of three separation distances, namely h = 3, 5, and 7 mm on the antenna performance in terms of |S11| response and peak gain, respectively. The corresponding effects of varying the AMC array size are shown in Fig. 6a,b, respectively. From the figures, it can be observed that with a spacing of 3 mm between the antenna and a 5 × 5 AMC array, strong resonance occurs at 2.45 GHz with a peak gain of 8 dBi. Also, it can be observed that the AMC surface caused a weak resonance at 2.7 GHz. This resonance can be reduced by increasing the space between the antenna and the AMC layer, but in return increasing the overall antenna size.

Effects of the spacing of the AMC surface on antenna performance with 5 × 5 array size. (a) |S11| response. (b) Peak gain.

Effects of the size of the AMC surface on antenna performance with 3 mm spacing. (a) |S11| response. (b) Peak gain.

In practical applications, the wearable antenna is expected to be bent during the operation. To ensure the reliability of the designed antenna for such a scenario, the integrated antenna was subjected to structural bend along both the x-axis (in the L direction) and the y-axis (in the W direction). Five different curvature radii along each of the x-axis (Rx) and y-axis (Ry), namely 40, 50, 60, 70, and 80 mm were separately studied. These values are reasonable representations of curvature radii of various rounded positions of the adult human body. The simulated |S11| responses versus frequency for both bending scenarios are displayed in Fig. 7a,b. In each scenario, the bending radius along one axis was changed and kept zero for the other (i.e. flat). As can be seen, the impedance BW of the bent AMC-backed antenna isn’t changing which indicates that the antenna has good suitability in such scenarios for operation. However, a slight upper-frequency shift appears for the bending scenario at the y-axis, especially with a curvature radius of 40 mm.

The |S11| response with different curvature radii. (a) Along x-axis. (b) Along y-axis.

In this section, the performance of the proposed wearable antenna backed by the designed AMC surface is investigated when considered for operation in the vicinity of human tissues at a distance of 1 mm. To simulate the antenna performance, the Hugo voxel-based body model presented in CST Microwave Suite was used. The Hugo model is an inhomogeneous human model built from 32 tissues. Each tissue has material properties that reflect the anatomical human tissue properties. In this study, the Hugo model allows the determination of the loading effect of the human body on antenna performance and a detailed analysis of the SAR distributions.

The antenna characteristics for flat and rounded body loading were studied. The evaluation was performed in terms of |S11| response and radiation characteristics. Figure 8a,b show with a good agreement the |S11| responses evaluated in free space in comparison to that of body loading for a flat back and rounded arm of radius 50 mm, respectively. The corresponding far-field radiation patterns are illustrated in Fig. 9. Slightly effect on antenna performance is observed when loaded onto the human body.

The |S11| response of the antenna evaluated in free space in comparison to that of body loading for (a) Flatback. (b) Arm of radius 50 mm.

The radiation patterns characteristics of the AMC-backed antenna at 2.45 GHz evaluated in free space (dashed) in comparison to that of body loading (solid) for (a) flatback. (b) Arm of radius 50 mm.

Figure 10 shows the radiation characteristics of the AMC-backed antenna in free space in comparison to that of body loading. The results show that the peak gain of the flat AMC-backed antenna in free space and when attached to the human back model is almost not affected, while a slight effect of 0.85 dB occurs in the peak gain of the bent antenna (Ry = 50 mm) when attached to the human arm. The radiation efficiency is almost stable and varies from 70 to 72% for all cases. As well the total efficiency is almost stable and varies around 60% for all cases.

Simulated radiation characteristics of the antenna in free space and when placed close to the human body model. (a) Peak gain, (b) radiation efficiency. (c) Total efficiency.

The SAR level is used to evaluate the amount of RF (radio frequency) energy absorbed by the human body. The Council of the European Union recommended a SAR value of 2 W/kg averaged over 10 g of tissues19. The SAR level is expressed as26:

where σ is the conductivity of the tissue in S/m, ρ is the mass density of the tissue in kg/m3, and E is the total RMS electric field strength in V/m.

The SAR distribution of the proposed wearable antenna system is evaluated, considering flat (human back) and rounded body (a human arm of radius 50 mm) models. Figure 11a shows the calculated 10 g averaged SAR for the flat antenna at 2.45 GHz. It can be seen that the calculated SAR value for the AMC-loaded antenna is 0.18 W/kg compared to 36.8 W/kg for the flat standalone antenna. The same scenario is shown in Fig. 11b for SAR distribution along the human arm. It can be seen that the calculated SAR value for the AMC-loaded antenna is 0.371 W/kg compared to 20.8 W/kg for the bent standalone antenna. From this evaluation, it can be seen that the SAR level is significantly reduced when the AMC reflector surface is used.

SAR values evaluated over 10 g of tissues of the proposed antenna alone (left) and over the AMC surface (right) at 2.45 GHz on (a) flatback. (b) Arm of radius 50 mm.

In order to examine the practical performance of the proposed wearable antenna system, prototypes were fabricated and subjected to measurement. The proposed antenna and the AMC surface were etched on a conductive layer of 0.035 mm thickness glued to a single layer and a double-compacted layer of cotton fabrics, respectively. The prototype performances were measured through an Agilent N9918A vector network analyzer, where a 50-Ω SMA (SubMiniature A) connector was used to feed the antenna. A comparison of simulated and measured |S11| responses of the proposed antenna is given in Fig. 12 for different design cases, the antenna alone in flat and bent states and over the AMC surface for both states. For bending analysis, the antenna was wrapped around a foam cylinder of radius Ry = 50 mm, corresponding to the approximate size of an adult human arm. It can be seen from Fig. 12 that the proposed antenna system can resonate around 2.45 GHz in all cases, with a good agreement between the simulated and measured frequency responses. The measured impedance BW equals 510 and 700 MHz for the antenna alone in flat and bent states, respectively, whereas equals 230 and 370 MHz for the AMC-backed antenna in flat and bent states, respectively, which is suitable for medical applications allocated at this band.

Simulated and measured |S11| responses of the proposed wearable antenna for different design cases. (a) Flat antenna. (b) Bent antenna (Ry = 50 mm). (c) Flat AMC-backed antenna. (d) Bent AMC-backed antenna (Ry = 50 mm).

For free space measurements, the radiation characteristics of the fabricated antenna prototypes for the four different design cases aforementioned before were assessed in an anechoic chamber StarLab 18 as shown in Fig. 13. Comparison between simulated and measured radiation patterns in the x–z plane and y–z plane at the operating frequency of 2.45 GHz is shown in Fig. 14. It is clear that monopole-like radiation patterns are obtained for the antenna alone in both states. The AMC-backed antenna in both states has a directional pattern which is desirable for medical applications. Figure 15 shows the measured and simulated antenna gain of the flat antenna with and without the AMC surface. The measured data were determined by comparing them to that of a reference standard gain horn antenna. A measured peak gain of 7.2 dBi was achieved at 2.45 GHz for the antenna with the AMC surface compared to a peak gain of 1.9 dBi for the antenna alone, with a good agreement between the simulated and measured frequency responses.

Antenna prototypes under test in an anechoic chamber. (a) Excluding AMC. (b) Including AMC.

Simulated (dashed line) and measured (solid line) radiation patterns of the proposed antenna system in the x–z plane and y–z plane at 2.45 GHz. (a) Flat antenna. (b) Bent antenna. (c) Flat AMC-backed antenna. (d) Bent AMC-backed antenna.

Simulated and measured peak gain of the proposed antenna in a flat state with and without AMC surface.

For real human on-body measurements, a prototype of the antenna backed with the AMC surface was placed close to an adult’s back and arm. The measured |S11| responses along with the simulated ones are shown in Fig. 16a,b, respectively. Good performance is obtained for the antenna at two on-body placements, which validates the design strategy.

The |S11| responses of the fabricated AMC-backed antenna prototype placed close to an adult’s (a) back. (b) Arm of radius 50 mm.

Table 1 compares the performance of the proposed single-band wearable antenna with state-of-the-art. Compared with the reported antennas of different substrates, the proposed integrated antenna features a good performance with all fabric-based substrates.

In this work, a cotton-based wearable antenna convenient to be integrated with clothing was developed for 2.45 GHz wearable applications. The antenna was printed on a 0.9 mm pure cotton fabric (εr = 1.7) with a small overall size of 30 mm × 36 mm × 0.9 mm. To mitigate the body coupling effect, an AMC surface was integrated behind the antenna. The structural deformation of the integrated antenna was analyzed in free space as well as when it was placed in the vicinity of the human body, indicating its good suitability for operation when bent at both the x-axis and the y-axis. Further investigation, the SAR evaluation in the Voxel-based human body model considering flat and rounded body parts indicates that the integrated antenna provided average SAR values below the critical rate. The proposed design also features a directional pattern with respect to the on-body with high radiation characteristics, which makes it attractive for potential wearable applications.

All data generated or analyzed during this study are included in this article (and there are no supplementary materials).

Kamalaveni, A. & Madhan, M. G. A compact TRM antenna with high impedance surface for SAR reduction at 1800 MHz. AEU Int. J. Electron. Commun. 70(9), 1192–1198. https://doi.org/10.1016/j.aeue.2016.06.002 (2016).

Article Google Scholar

Hall, P. S. & Hao, Y. Antennas and Propagation for Body-Centric Wireless Communications (Artech House, 2012).

Google Scholar

Ibrahim, A. A., Ahmed, M. I. & Ahmed, M. A systematic investigation of four ports MIMO antenna depending on flexible material for UWB networks. Sci. Rep. 12(1), 1–16. https://doi.org/10.1038/s41598-022-18551-8 (2022).

Article MathSciNet CAS Google Scholar

Conway, G. A. & Scanlon, W. G. Antennas for over-body-surface communication at 2.45 GHz. IEEE Trans. Antennas Propag. 57(4), 844–855. https://doi.org/10.1109/TAP.2009.2014525 (2009).

Article ADS Google Scholar

Alemaryeen, A. & Noghanian, S. On-body low-profile textile antenna with artificial magnetic conductor. IEEE Trans. Antennas Propag. 67(6), 3649–3656. https://doi.org/10.1109/TAP.2019.2902632 (2019).

Article ADS Google Scholar

Smida, A. et al. Wideband wearable antenna for biomedical telemetry applications. IEEE Access 8, 15687–15694. https://doi.org/10.1109/ACCESS.2020.2967413 (2020).

Article Google Scholar

Elias, B. B. Q., Soh, P. J., Al-Hadi, A. A. & Akkaraekthalin, P. Gain optimization of low-profile textile antennas using CMA and active mode subtraction method. IEEE Access 9, 23691–23704. https://doi.org/10.1109/ACCESS.2021.3056905 (2021).

Article Google Scholar

Saadat, W., Raurale, S. A., Conway, G. A. & McAllister, J. Wearable antennas for human identification at 2.45 GHz. IEEE Trans. Antennas Propag. 70(1), 17–26. https://doi.org/10.1109/TAP.2021.3090852 (2022).

Article ADS Google Scholar

Mahfuz, M. H. et al. Wearable textile patch antenna: Challenges and future directions. IEEE Access 10, 38406–38427. https://doi.org/10.1109/ACCESS.2022.3161564 (2022).

Article Google Scholar

Hassan, W. M., Saad, A. A. R. & Ibrahim, A. A. Ultra-wide band flexible antenna applicable for dual-band on-body communications. Int. J. Microw. Wirel. Technol. https://doi.org/10.1017/S1759078722000514 (2022).

Article Google Scholar

Boyuan, M., Pan, J., Wang, E. & Yang, D. Wristwatch-style wearable dielectric resonator antennas for applications on limps. IEEE Access 8, 59837–59844. https://doi.org/10.1109/ACCESS.2020.2983098 (2020).

Article Google Scholar

Wang, M. et al. Investigation of SAR reduction using flexible antenna with metamaterial structure in wireless body area network. IEEE Trans. Antennas Propag. 66(6), 3076–3086. https://doi.org/10.1109/TAP.2018.2820733 (2018).

Article ADS Google Scholar

Zu, H. R. et al. Circularly polarized wearable antenna with low profile and low specific absorption rate using highly conductive graphene film. IEEE Antennas Wirel. Propag. Lett. 19(12), 2354–2358. https://doi.org/10.1109/LAWP.2020.3033013 (2020).

Article ADS Google Scholar

Ullah, M. A., Islam, M. T., Alam, T. & Ashraf, F. B. Paper-based flexible antenna for wearable telemedicine applications at 2.4 GHz ISM band. Sensors 18(12), 4214. https://doi.org/10.3390/s18124214 (2018).

Article ADS PubMed PubMed Central Google Scholar

Labiano, I. I. & Alomainy, A. Flexible inkjet-printed graphene antenna on Kapton. Flex. Print. Electron. 6(2), 025010. https://doi.org/10.1088/2058-8585/ac0ac1 (2021).

Article CAS Google Scholar

Yang, H., Liu, X. & Fan, Y. Design of broadband circularly polarized all-textile antenna and its conformal array for wearable devices. IEEE Trans. Antennas Propag. 70(1), 209–220. https://doi.org/10.1109/TAP.2021.3098542 (2022).

Article ADS Google Scholar

Ferreira, D., Pires, P., Rodrigues, R. & Caldeirinha, R. F. Wearable textile antennas: Examining the effect of bending on their performance. IEEE Antennas Propag. Mag. 59(3), 54–59. https://doi.org/10.1109/MAP.2017.2686093 (2017).

Article ADS Google Scholar

IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz 1999 th edn. IEEE Std C 95.1 1–83.

Kaim, V. et al. Ultra-miniature circularly polarized CPW-fed implantable antenna design and its validation for biotelemetry applications. Sci. Rep. 10(1), 1–16. https://doi.org/10.1038/s41598-020-63780-4 (2020).

Article CAS Google Scholar

Chen, Y. S. & Ku, T. Y. A low-profile wearable antenna using a miniature high impedance surface for smart watch applications. IEEE Antennas Wirel. Propag. Lett. 15, 1144–1147. https://doi.org/10.1109/LAWP.2015.2496366 (2015).

Article ADS Google Scholar

Wissem, E. M., Sfar, I., Osman, L. & Ribero, J. M. A textile EBG-based antenna for future 5G-IoT millimeter-wave applications. Electronics 10(2), 154. https://doi.org/10.3390/electronics10020154 (2021).

Article CAS Google Scholar

Abbasi, M. A. B., Nikolaou, S. S., Antoniades, M. A., Stevanović, M. N. & Vryonides, P. Compact EBG-backed planar monopole for BAN wearable applications. IEEE Trans. Antennas Propag. 65(2), 453–463. https://doi.org/10.1109/TAP.2016.2635588 (2016).

Article ADS Google Scholar

Ashyap, A. Y. et al. Compact and low-profile textile EBG-based antenna for wearable medical applications. IEEE Antennas Wirel. Propag. Lett. 16, 2550–2553. https://doi.org/10.1109/LAWP.2017.2732355 (2017).

Article ADS Google Scholar

Velan, S. et al. Dual-band EBG integrated monopole antenna deploying fractal geometry for wearable applications. IEEE Antennas Wirel. Propag. Lett. 14, 249–252. https://doi.org/10.1109/LAWP.2014.2360710 (2014).

Article ADS Google Scholar

Abirami, B. S. & Sundarsingh, E. F. EBG-backed flexible printed Yagi–Uda antenna for on-body communication. IEEE Trans. Antennas Propag. 65(7), 3762–3765. https://doi.org/10.1109/TAP.2017.2705224 (2017).

Article ADS Google Scholar

Nie, H. K. et al. Wearable antenna sensor based on EBG structure for cervical curvature monitoring. IEEE Sens. J. 22(1), 315–323. https://doi.org/10.1109/JSEN.2021.3130252 (2022).

Article ADS CAS Google Scholar

Saeed, S. M., Balanis, C. A., Birtcher, C. R., Durgun, A. C. & Shaman, H. N. Wearable flexible reconfigurable antenna integrated with artificial magnetic conductor. IEEE Antennas Wirel. Propag. Lett. 16, 2396–2399. https://doi.org/10.1109/LAWP.2017.2720558 (2017).

Article ADS Google Scholar

Agarwal, K., Guo, Y. X. & Salam, B. Wearable AMC backed near-endfire antenna for on-body communications on latex substrate. IEEE Trans. Compon. Packag. Manuf. Technol. 6(3), 346–358. https://doi.org/10.1109/TCPMT.2016.2521487 (2016).

Article Google Scholar

Ibrahim, A. A. & Ali, W. A. High gain, wideband and low mutual coupling AMC-based millimeter wave MIMO antenna for 5G NR networks. AEU Int. J. Electron. Commun. 142, 153990. https://doi.org/10.1016/j.aeue.2021.153990 (2021).

Article Google Scholar

Mantash, M., Tarot, A. C., Collardey, S. & Mahdjoubi, K. Design methodology for wearable antenna on artificial magnetic conductor using stretch conductive fabric. Electron. Lett. 52(2), 95–96. https://doi.org/10.1049/el.2015.3135 (2016).

Article ADS Google Scholar

Abdelghany, M. A., Fathy Abo Sree, M., Desai, A. & Ibrahim, A. A. Gain Improvement of a dual-band CPW monopole antenna for Sub-6 GHz 5G applications using AMC structures. Electronics 11(14), 2211. https://doi.org/10.3390/electronics11142211 (2022).

Article Google Scholar

Lago, H. et al. Textile antenna integrated with compact AMC and parasitic elements for WLAN/WBAN applications. Appl. Phys. A 122(12), 1–6. https://doi.org/10.1007/s00339-016-0575-9 (2016).

Article CAS Google Scholar

Alemaryeen, A. & Noghanian, S. Crumpling effects and specific absorption rates of flexible AMC integrated antennas. IET Microw. Antennas Propag. 12(4), 627–635. https://doi.org/10.1049/iet-map.2017.0652 (2018).

Article Google Scholar

Raad, H. R., Abbosh, A. I., Al-Rizzo, H. M. & Rucker, D. G. Flexible and compact AMC based antenna for telemedicine applications. IEEE Trans. Antennas Propag. 61(2), 524–531. https://doi.org/10.1109/TAP.2012.2223449 (2013).

Article ADS Google Scholar

Zhang, K., Vandenbosch, G. A. & Yan, S. A novel design approach for compact wearable antennas based on metasurfaces. IEEE Trans. Biomed. Circuits Syst. 14(4), 918–927. https://doi.org/10.1109/TBCAS.2020.3010259 (2020).

Article PubMed Google Scholar

Joshi, R. et al. Dual-band, dual-sense textile antenna with AMC backing for localization using GPS and WBAN/WLAN. IEEE Access 8, 89468–89478. https://doi.org/10.1109/ACCESS.2020.2993371 (2020).

Article Google Scholar

Kumar, A., Kumar, A. & Kumar, A. Gain enhancement of a wideband rectangular ring monopole millimeter-wave antenna using artificial magnetic conductor structure. Int. J. RF Microw. Comput. Aided Eng. 32(10), e23319. https://doi.org/10.1002/mmce.23319 (2022).

Article Google Scholar

Dwivedi, R. P., Khan, M. Z. & Kommuri, U. K. UWB circular cross slot AMC design for radiation improvement of UWB antenna. AEU Int. J. Electron. Commun. 117, 153092. https://doi.org/10.1016/j.aeue.2020.153092 (2020).

Article Google Scholar

Download references

Open access funding provided by The Science, Technology & Innovation Funding Authority (STDF) in cooperation with The Egyptian Knowledge Bank (EKB). There are no funds, grants, or other support received to conduct this study.

Kosseir Radio, Telecom Egypt, Kosseir, 84712, Egypt

Ayman Ayd R. Saad

Electronics Research Institute, El-Nozha El-Gadida, Cairo, 11843, Egypt

Walaa M. Hassan

Electronics and Communications Engineering Department, Minia University, Minia, 61111, Egypt

Ahmed A. Ibrahim

You can also search for this author in PubMed Google Scholar

A.A.R.S. and A.A.I. wrote the main manuscript text, prepared figures and simulation results. W.M.H. achieved the fabrication and measurements simulation results and prepared some of figures. All authors reviewed the manuscript.

Correspondence to Ahmed A. Ibrahim.

The authors declare no competing interests.

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

Ayd R. Saad, A., Hassan, W.M. & Ibrahim, A.A. A monopole antenna with cotton fabric material for wearable applications. Sci Rep 13, 7315 (2023). https://doi.org/10.1038/s41598-023-34394-3

Download citation

Received: 25 January 2023

Accepted: 28 April 2023

Published: 05 May 2023

DOI: https://doi.org/10.1038/s41598-023-34394-3

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.